Where: Texas
Products:  ranchwood™ product line in southern finish color with circle sawn texture. Wood substrate is douglas fir.
Product Use:  1×12 board and 1×3 batten and 1×6 trim.  8×12, 8×8, 4×8 posts in circle sawn texture all FOHC #1 kiln dried timbers.  Rafter tails 2×6 and 3×6 in douglas fir material. Garage door and barn door material is 1×6 and 2×6.

Montana Timber Products offers 4 product lines in douglas fir or cedar wood species (each in three grades).  Along with corral board an authentic reclaimed wood.   Materials are available in 4″, 6”, 8”, 10” and 12″ wide boards in lengths ranging from 4ft to 16ft long (douglas fir or western red cedar).  Available in 6 profiles (shiplap, square edge, square edge lap, shiplap reveal, tongue and groove, channel rustic) and 3 textures for the AquaFir™ and ranchwood™ products (smooth, wire brushed, circle sawn), ranchwood™ Artisan is ONE texture (raked) and Charwood™ is its own texture from the burning.  Thickness offered is 1″,5/4 (cedar only), 2″ as standards and then timbers/posts in 3+ inches.  The board will come profiled, textured, stained on one side (unless you designate needing more sides stained) and sealed on all 4 sides with our seal once.  Call 406-215-4961 for more information or fill out the contact form at:  http://www.montanatimberproducts.com/contact/.

Where:  Wyoming
Products:  AquaFir™ product line in driftwood wire brushed siding, soffit, fascia, trim, and timber. All in douglas fir.

Product Use:  1×6 shiplap with 1/8” reveal vertical siding.  1×8 shiplap with 1/8” reveal for garage doors. Soffit and overhang ceilings are 1×6 tongue and groove material.  1×8 fascia, 2×4, 2×6 window trim,  2×8 door and corner trim.  Timbers 8×8, 3×4 and 4×4, all for the front entry.

AquaFir™ is offered in 3 textures: smooth, wire brush and circle sawn, each offer a different look and change the appearance to personalize the project.  Along with different textures and profiles, you can customize your wood species, with douglas fir or cedar. All of our product lines can be used for siding, timbers, trusses, posts, beams, decks, siding, trim, fascia, soffit, interior paneling/ceiling,, etc…

In extreme climates, acclimation and installation are crucial. Montana Timber Products helps by stabilizing any board wider than 6″ by doing relief cuts. Relief cuts (kerf cuts) are milled on the back of the siding and create air circulation.  In addition to relief cuts, Montana Timber Products uses SEAL-ONCE® to seal the entire board in a controlled environment to protect the wood from water damage.  Ask your sales representative for guidance to find what grade of wood and species best fit your needs.

Our ranchwood™, AquaFir™, ranchwood™ Artisan, ranchwood™ weathered, Charwood™, and Corral Board product lines offer a full selection of exterior and interior wood materials.  All the products can be used for residential and commercial application.  Each product line is offered in two wood species, Douglas Fir and Cedar in various grades, talk to a Montana Timber Products representative to find out what fits your design and budget best.  Call 406-215-4961 for more information or fill out the contact form at:  http://www.montanatimberproducts.com/contact/.

Where:  Montana
Products:  ranchwood™ in tackroom color with circle sawn texture, for the trim, siding, soffit, fascia, all in cedar.  The timbers are resawn, FOHC douglas fir in tackroom color.
Product Use:  1×4 vertical shiplap, 1×6 vertical shiplap, and 1×10 horizontal shiplap profile. 1×4,1×6 square edge material for window, door, and corner trim.  Gable accent 2×8 and 2×4 and 4×4 posts.  Soffit material: Breckenridge plywood 5/8”x4x8 panels.

Using the siding material on the garage doors transforms a bland door into a focal point.  Creating a finished look to create a nice impact effortlessly.  Cedar is lightweight, aesthetically pleasing for any style home. The durability and variety of grades (STK-select tight knot, CMG-clear mixed grain, CVG clear vertical grain) give homeowners many choices.

Montana Timber Products is a leading manufacturer of specialty pre-finished wood and reclaimed wood products.  Our process allows us to customize each order to meet the customers design needs.  The extensive line of products include:  siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking, fencing, and glulam beams.  Customers enjoy mill direct pricing, flexibility to customize colors and profiles. To get a quote or more information call 406-215-4961 or fill out the contact form at:  http://www.montanatimberproducts.com/contact/

Where:  Oregon
Products:  Aquafir™ in battleship color and ranchwood™ in southern for the siding material.  Trimmed with  Aquafir™ brown trim, fascia and soffit.  All the material is douglas fir with wire brush texture.
Product Use:  1×4,1×6, 1×8 in battleship and 1×10 shiplap in southern siding. 1×4,1×6 and 1×10 square edge material for window, door and corner trim all in brown.

Mixing sizes and colors for this vertical and horizontal shiplap siding helped create a subtle difference.  This traditional mountain style home is one of a kind.  The clean lines pay homage to its rural setting, while keeping the design exquisitely simple.  ranchwood™ product provides a reclaimed look while enjoying all the advantages of working with new wood.

Montana Timber Products is a specialty wood products manufacturer.  Creating rustic, modern and contemporary wood siding, interior accents, reclaimed wood, and barn wood alternatives.  Our ranchwood™, AquaFir™, ranchwood™ Artisan, ranchwood™ weathered, Charwood™, and Corral Board products offer a selection of exterior and interior wood materials.  All products can be used for residential and commercial application.  Each product line is offered in two wood species, Douglas Fir and Cedar.  Seal-Once offers high performance long lasting waterproofing seal that is environmentally friendly non-toxic protection.  Selling direct to the customer allows Montana Timber Products flexibility to create your project.  Call 406-215-4961 for more information or fill out the contact form at:  http://www.montanatimberproducts.com/contact/.

Where:  Idaho/Wyoming
Products: ranchwood™ Artisan product line in ash color with raked texture in cedar.  ranchwood™ product line in tackroom color with wire brush texture in cedar and timbers in FOHC Douglas fir tackroom color with wire brush texture.
Product Use:  Board and Batten with 1×10 and 1×4 square edge materials for siding. 1×6 tongue and groove soffit and 2×6 T&G gable ceilings, 1×6 tongue and groove garage door material with 1×6 and 1×10 square edge boards to accent all in cedar, raked texture and Ash color.  2×4 trim for sills and windows, 2×6 door and window trim, 2×8 and 2×10 horizontal bands, 1×8 and 1×4 fascia in cedar, ranchwood™ tackroom color with wire brushed texture. 3x8x12 rafters, beams/columns: 6x6x4, 6x8x6-14, 6x10x12-14,6x12x12,   8x8x8-12, 8x12x8-16, 8x14x14-18, 8x20x14, 10x10x10-12, 10x12x10, 10x14x8-24 all are FOHC douglas fir (free of heart center) kiln dried wire brushed texture in tackroom color from the ranchwood™ product line.

Building at high elevations in the fall can create challenges.  Early freezes, rain, and morning dew can all create wet conditions making it difficult to schedule exterior painting or staining.  Pre-finished wood created in a controlled environment eliminates the peeling and cracking of paint and stain that was applied in poor weather conditions.  Ideal painting weather is 50-85 degrees with little wind and humidity. Most stains and paint are formulated to dry, ideally not in weather below 32 degrees, which creates longer drying times and more potential for problems.

Montana Timber Products environmentally friendly process applies the stain and seals the entire board in a controlled environment eliminating the guessing game in a builder’s schedule.  Every order is hand crafted to create the beauty custom home builders and homeowners require.  Creating the perfect look for siding, trim, soffit, fascia, and all the timbers in one place is easy, just call us to get started 406-215-4961.

Montana Timber Products is a leading manufacturer of specialty pre-finished wood and reclaimed wood products.  Our process allows us to customize each order to meet the customers design needs.  The extensive line of products include:  siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking, fencing, and glulam beams.  Customers enjoy mill direct pricing, quick delivery, exceptional quality, flexibility to customize colors and profiles. To get a quote or more information call 406-215-4961 or fill out the contact form at:  http://www.montanatimberproducts.com/contact/

Where: Michigan
Product:  ranchwood™ siding and interior wall cladding in southern color with circle sawn texture in douglas fir
Product Use:  1×8 shiplap

Montana Timber Products is a leading manufacturer of specialty pre-finished wood and reclaimed wood products.  Our process allows us to customize each order to meet the customers design needs.  The extensive line of products include:  siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking and glulam beams.  Customers enjoy mill direct pricing, quick delivery, exceptional quality, flexibility to customize colors and profiles. To get a quote or more information call 406-215-4961 or fill out the contact form at:  http://www.montanatimberproducts.com/contact/

Product: ranchwood™ Artisan Ash color in douglas fir used throughout every component of the exterior on the cabin.
Product Use: 1×8 shiplap, 1×6 tongue and groove soffit, 1×4,1×8 and 1×12 fascia, 1×4 and 1×8 window and door trim, 2×2 corner trim and the timbers, posts and beams ranged in size from 6x6x12 to 6x14x24.

This 6,700 acre development worked with Montana Timber Products to produce product for the cabins (below), custom homes and the clubhouse. Each project kept the beauty of the surroundings in mind and maintained a mountain modern look. Working with developers to find the right look, stay in budget, and keep the project on schedule is something Montana Timber Products provides throughout the United States.

Montana Timber Products is the leading manufacturer in specialty pre-finished wood and reclaimed wood products. This development used our expertise to deliver pre-finished products right to the job site for multiple home sites, helping the project stay on time and in budget.   Pre-finished products help to build year-round and keep the product color, quality and integrity all consistent.   Whether your project is for residential or commercial, we provide custom wood materials for interior and exterior use in more than 39 colors and two wood species (douglas fir and cedar). Let us be apart of creating your dream project. Call 406-215-4961 for more information or fill out the contact form at: http://www.montanatimberproducts.com/contact/

Where: Colorado
Product: ranchwood™ siding (douglas fir), soffit (cedar), trim (cedar), fascia (cedar)– 1st floor Western color in circle sawn texture, 2nd floor Southern color in Wire Brush texture
Product use: 1st floor 1×10 Horizontal shiplap, 2nd floor 1×6 vertical shiplap, Fascia 2×10 and 2×6, Soffit 1×6 T&G, Trim 2×6, 2×8, 2×10 and 2×12.

Montana Timber Products is the leading manufacturer of specialty pre-finished wood and reclaimed wood products. Our process allows us to customize each order to meet the customers needs. The extensive line of products include: siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking and glulam beams. Customers enjoy mill direct pricing, quick delivery, exceptional quality, flexibility to customize colors and profiles. To get a quote or more information call 406-215-4961 or fill out the contact form at: http://www.montanatimberproducts.com/contact/

Where: Montana
Product: ranchwood™ siding, trim, soffit, fascia, and timbers are all in douglas fir circle sawn texture in eastern color.
Product Use: 1×4, 1×6, 1×8 shiplap siding and 1×10 square edge lap siding, corner trim 2×8, window trim 2×6, garage trim 1×10, timbers in 6×8, 8×8 and 8×12.

Montana Timber Products is a leading manufacturer of specialty pre-finished wood and reclaimed wood products. Our process allows us to customize each order to meet the customer’s needs. The extensive line of products include: siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking and glulam beams. Customers enjoy mill direct pricing, quick delivery, exceptional quality, flexibility to customize colors and profiles. To get a quote or more information call 406-215-4961 or fill out the contact form at: http://www.montanatimberproducts.com/contact/

Where:  Colorado

Product: ranchwood™, and AquaFir™ douglas fir, find information at: http://www.montanatimberproducts.com/products/

Product Use: Circle sawn ranchwood™ in greenhorn color with shiplap siding using 1×4, 1×6, and 1×8 material.  Wire brush AquaFir™ in brown color used for: channel rustic siding in 1×8, 1×6 tongue and groove soffit, square edge product for trim in 1×4 and 1×8, fascia in 1×6 and 2×10, garage door headers 3x12x22, deck skirt in 1×6 and 1×12.

Mixing the ranchwood™ and AquaFir™ products along with different profiles (shiplap and channel rustic) gave this duplex a gorgeous exterior.  Combining wood, metal and masonry add layers of texture to create a beautiful aesthetic.

Montana Timber Products is a leading manufacturer of specialty pre-finished wood and reclaimed wood products.  Our process allows us to customize each order to meet the customers needs.  The extensive line of products include:  siding, trim, soffit and fascia, interior accents, timbers, fabricated trusses, decking and glulam beams.  Customers enjoy mill direct pricing, quick delivery, exceptional quality, flexibility of customized colors and profiles.  For a quote or more information call 406-215-4961 or fill out the contact form at:  http://www.montanatimberproducts.com/contact/.